Cub Cadet I1042 Manuale Utente

CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOp e r a t O r ’s Ma n u a lSafe Operation Practices • Set-Up • Operation • Ma

10 se c t i O n 3— as s e M b l y & se t -upPosition the red rubber boot over the positive battery 3. terminal to help protect it from corrosion

Controls & Features411Hood Lift NotchKey Switch ModulePTO (Blade Engage)Control SwitchForward Control PedalReverse Control PedalParking Brake Leve

12 se c t i O n 4— cO n t r O l s & fe a t u r e sBattery Indicator LightIlluminates when the ignition switch it turned to an ON position and th

13se c t i O n 4 — cO n t r O l s & fe a t u r e sForward Control PedalThe forward control pedal is located on the right side of the tractor, at

Operation514WARNING! To Avoid serious injury or death:Go up and down slopes, not across.• Avoid sudden turns.• Do not operate the tractor where it cou

15se c t i O n 5 — Op e r a t i O nThe Reverse Caution Mode will remain activated until:7. The key is placed in either the Normal Mowing a. position

16 se c t i O n 5— Op e r a t i O nIncreasing the turn of the steering wheel (beyond 10°-• 15º) results in increasingly tighter turns. As the steerin

Maintenance & Adjustments617Maintenance ScheduleBefore Each useEvery 10 HoursEvery 25 HoursEvery 50 HoursEvery 100 HoursPrior to StoringClean Hoo

18 se c t i O n 6— Ma i n t e n a n c e & ad j u s t M e n t sTurn the oil drain valve a. ⁄-turn, then pull outward to begin draining oil. Af

19se c t i O n 6 — Ma i n t e n a n c e & ad j u s t M e n t sUsing Deck Wash System™Use the Deck Wash System™ to rinse grass clippings from the

Customer SupportIf you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this machine

20 se c t i O n 6— Ma i n t e n a n c e & ad j u s t M e n t sLower Frontof DeckRaise Frontof DeckFigure 6-6Side to Side Leveling the DeckNOTE:

21se c t i O n 6 — Ma i n t e n a n c e & ad j u s t M e n t sDeck Gauge Wheel AdjustmentNOTE: The deck gauge wheels are an anti-scalp feature

Service722Pivot Bar AdjustmentIf excessive play is experienced in the steering wheel, check the pivot bar for forward/rearward movement. Raise the fro

23se c t i O n 7 — se r v i c eOff-Season StorageIf the machine is to be inoperative for a period longer than 30 days, the following procedures are r

24 se c t i O n 7— se r v i c eCutting BladesWARNING! Be sure to shut the engine off, remove ignition key, disconnect the spark plug wire(s) to preve

25se c t i O n 7 — se r v i c eLoop the belt and push out of the V- groove of the drive 3. pulley on the right hand spindle assembly. Lift the belt

26 se c t i O n 7— se r v i c eRe-install the idler bracket backstop components as 14. originally installed in the deck housing, and position so that

Troubleshooting827Problem Cause RemedyExcessive vibration Cutting blade loose or unbalanced. 1. Damaged or bent cutting blade. 2. Tighten blade and s

Replacement Parts928Phone (800) 800-7310 to order replacement parts or a complete Parts Manual (have your full model number and serial number ready).

29se c t i O n 9 — re p l a c e M e n t pa r t sPhone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model num

Important Safe Operation Practices23General OperationRead, understand, and follow all instructions on the 1. machine and in the manual(s) before attem

Attachments & Accessories1030The following attachments and accessories are compatible for Cub Cadet i1042. See your Cub Cadet dealer or the retail

Notes1131

32 se c t i O n 11— nO t e s

33se c t i O n 11 — nO t e s

FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSMTD Consumer Group Inc, the United States Environment

GDOC-100223 Rev. AWARRANTED PARTS:The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such w

IMPORTANT: To obtain warranty coverage owner must present an original proof of purchase and applicable maintenance records to the servicing dealer. Pl

4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sA missing or damaged discharge cover can cause blade 12. contact or th

5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sChildrenTragic accidents can occur if the operator is not alert to the

6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sPeriodically check to make sure the blades come to 3. complete stop wi

7se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may a

8 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e s15°Sight and hold this level with a vertical tree...or a corner of a b

Assembly & Set-Up39Moving the Tractor ManuallyIf for any reason the tractor will not drive or you wish to move the tractor, engage the two hydro t